![]() ![]() I next go to the step where you open and close any door and I hear the same 8 beeps. I also believe it's in programming mode because when I press the unlock button on the door of the car I hear the same different style beep. I hear a series of 8 beeps once I turn the key and the beeps sound different than the ones you hear if you leave the key in the ignition and open a door. At first, I think I wasn't entering programming mode because I had not turned the key fast enough - I think it's slightly faster than 1 second needed to switch it back on. So I verified the battery was good on both and tried to reprogram and it's not working. I believe what happened is they activated in my pocket too many times and then lost the sync with the car. Those worked great for several weeks though they were a bit more sensitive since the buttons weren't worn down like the old ones. ![]() So I went on ebay and bought two new shells and rubber button membranes parts and used the existing circuit boards. However, the rubber piece that has the buttons on it started to fall apart so that the buttons were coming apart from the rest of the rubber. History: I bought the car a few years ago and the person who sold it to me gave me 2 remotes that worked fine. I know this is an old thread, but I was wondering if anyone know anything about programming the key fobs beyond the procedure listed above? I found the one Bill posted on a dozen different sites and I have tried it about 2 dozen times now, but no luck. Install the "MALL PGM" fuse back into the fuse panel and test remote(s). Repeat step 7 now for each additional remotes to be programmed including any existingġ0. *** that will confirm successful programming.Ĩ. It is necessary to wait approximately 14 seconds for a second chime ************* IMPORTANT: After 7 seconds, a chime may be heard confirming successful Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds. A chime will be heard when the system enters intoħ. Turn the key to OFF and then back to ACC within 1 second.Ħ. Insert the key into the ignition, and turn to the ACC position.ĥ. *** owner's manual to properly locate the "MALL PGM" fuse.Ĥ. Remove the "MALL PGM" fuse from the fuse panel. The other remotes will not be functional until youģ. IMPORTANT: Before entering programming mode, have in possession all of the remotes you Remove the ignition key in order to exit the Program Mode. Perform the previous step to program up to four transmitters (including yourġ1. Transmitter has been successfully programmed (this take approximately 15ġ0. Transmitter and hold until the vehicle beeps twice to verify that the ![]() Press the LOCK and UNLOCK buttons together on the keyless entry Verify the Program Mode has been activated.ĩ. The vehicle will sound three beeps in order to Ignition key in the lock cylinder.) Leave the ignition key in the ignition lockĨ. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.)ħ. Insert the ignition key into the ignition lock cylinder and remove the key. | (Do not turn the ignition key in the lock cylinder.)Ħ. Press and hold the driver side door lock switch in the UNLOCK position.ĥ. Turn ignition OFF and remove the key from the ignition.Ĥ. Insert key in ignition and turn to ON (As far as you can without cranking engine)ģ. The other remotes will not be functional until you program the remotes again.Ģ. Once you program the remotes, all previous codes will be erased from the memory. IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Disconnect programming connector wire from ground to exit programming Repeat step 4 for to program any additonal keyless remotes includingĪnd existing keyless remotes. System will respond by lockingĪnd unlocking doors one time to indicate successful programming.ĥ. System will now lock and unlock doors automatically to indicateĤ. Leave connector wire connected to ground through out procedure.ģ. The programming connector wire should have one termial in the plasticĬonnector on end of black/white wire. You may have to pull back right side trunk trim on trunk wall to locateĢ. Locate the programming connector wire located in the RH trunk area. Note: Existing keyless remotes will be erased with this procedure.Įxisting working remotes will have to reprogrammed also.ġ. ![]()
0 Comments
Leave a Reply. |